<dd id="4hjov"></dd>

  • <li id="4hjov"><acronym id="4hjov"><u id="4hjov"></u></acronym></li>

    <rp id="4hjov"></rp>
    <rp id="4hjov"></rp>
    <button id="4hjov"><object id="4hjov"><menuitem id="4hjov"></menuitem></object></button>
    <button id="4hjov"><acronym id="4hjov"><kbd id="4hjov"></kbd></acronym></button>
    87福利午夜福利视频
    您好,歡迎光臨萊州中科聚峰機械有限公司網站! 主營自動攪拌車,攪拌一體車,自動上料攪拌車等各種規格的產品。

    自動上料攪拌車行業持續領跑者!

    點擊撥打服務熱線:4008791999

    您的位置:首頁 - 新聞中心 > 常見問題 >

    攪拌車離合器掛擋不佳時怎么解決?

    發布時間:2021-08-11 來源:http://www.junjungdrajat.com/ 瀏覽量:

    概述:1檢查攪拌車離合器踏板自由行程是否過大,然后進行調整。1 check whether the free stroke of the clutch pedal of the mixer
    1檢查攪拌車離合器踏板自由行程是否過大,然后進行調整。
    1 check whether the free stroke of the clutch pedal of the mixer is too large, and then adjust it.
    2檢查攪拌車分離杠桿,是否高度一致或存在過低的現象。具體方法:在車下撥動分離撥叉,使攪拌車分離軸承前端靠在分離杠桿內端面上,將離合器轉動一周。如果分離杠桿內端同時和分離軸承接觸不上,說明分離杠桿高度不一致,需要調整。
    2. Check whether the separation lever of the mixer truck has the same height or is too low. Specific method: move the release fork under the vehicle to make the front end of the release bearing of the mixer lean against the inner end face of the release lever, and rotate the clutch for one cycle. If the inner end of the release lever does not contact with the release bearing at the same time, it indicates that the height of the release lever is inconsistent and needs to be adjusted.
    自動攪拌車
    如果高度一致,仍然分離不徹底,此時應檢查杠桿高度。將各分離杠桿調到同一高度,如果分離徹底,說明原來調整不當或磨損嚴重。調整分離杠桿之后,離合器踏板的自由行程也必須重新調整。
    If the height is consistent and the separation is still incomplete, check the lever height at this time. Adjust the separation levers to the same height. If the separation is complete, it indicates that the original adjustment is improper or seriously worn. After adjusting the release lever, the free travel of the clutch pedal must also be readjusted.
    3進行上述操作后,如果還存在分離不徹底的情況,就要拆下離合器,檢查主從動盤有無翹曲、從動盤是否裝反、分離杠桿螺釘是否松動等。
    3 after the above operations, if the separation is not complete, remove the clutch and check whether the master-slave disc is warped, whether the driven disc is installed reversely, and whether the release lever screw is loose.
    4對于新鉚的摩擦片的離合器,要檢查從動盤和摩擦片是否過厚。如果過厚,可在離合器蓋和飛輪之間加墊片。
    4 for the clutch with newly riveted friction plate, check whether the driven plate and friction plate are too thick. If it is too thick, add shims between the clutch cover and the flywheel.
    5 對于混凝土攪拌車液壓傳動的離合器,除上述檢查外,還應檢查制動液是否缺少,管道是否滲漏并排出液壓系統內的空氣。
    5 for the hydraulic clutch of concrete mixer truck, in addition to the above inspection, check whether the brake fluid is missing, whether the pipeline leaks and exhaust the air in the hydraulic system.
    好的產品成就好的服務,好的廠家成就好的作品, 自動攪拌車堅持為客戶提供優質的服務,詳情請繼續關注我們的網站:http://www.junjungdrajat.com
    Good products make good services, and good manufacturers make good works. Automatic mixer truck insists on providing customers with high-quality services. Please continue to pay attention to our website for details: http://www.junjungdrajat.com

    截屏,微信識別二維碼

    微信號:

    點擊微信號復制,添加好友

     打開微信